Quick answer: A mount must pass two separate checks: fixture-to-bracket and tank-to-clamp. A compatible light bracket does not establish that the clamp fits your aquarium.
Print the two worksheets below or paste them into your own notes. Nothing on this page saves or submits, so your measurements stay with you.
Use the maker’s limits, not the fixture brand alone
EcoTech’s RMS Single Arm specification page lists maximum tank/trim thickness of 1-3/8 inches, clamp dimensions of 3.5 × 3.25 × 3 inches and 13 inches clearance above the RMS. Those dimensions apply to the named mount, not every arm. Its manuals page also separates single- and multi-light hardware. Match generation and bracket explicitly; an old manual’s model list should not be extrapolated to a later fixture.
Fixture-to-mount worksheet
| Connection | My fixture / part | Mount requirement and source | Verified? |
|---|---|---|---|
| Fixture brand, full model and generation | ________________ | ________________ | ________________ |
| Matching bracket / adapter part number | ________________ | ________________ | ________________ |
| Number of fixtures and supported configuration | ________________ | ________________ | ________________ |
| Required screws / supplied adapters | ________________ | ________________ | ________________ |
| Maker-approved orientation and assembly instructions | ________________ | ________________ | ________________ |
Tank-to-clamp worksheet
| Measurement | My tank / units | Documented mount limit | Pass / unknown |
|---|---|---|---|
| Panel material and thickness | ________________ | ________________ | ________________ |
| Rim / trim width, depth and shape | ________________ | ________________ | ________________ |
| Flat contact area inside and outside tank | ________________ | ________________ | ________________ |
| Back-wall clearance for clamp | ________________ | ________________ | ________________ |
| Horizontal reach to intended fixture center | ________________ | ________________ | ________________ |
| Height, lid hinge travel and service lift path | ________________ | ________________ | ________________ |
Thickness alone is not enough: a molded rim, eurobrace or overflow can prevent correct contact. Do not place a clamp on a brace or panel location the aquarium or mount maker excludes. Ask both makers if the contact surface is ambiguous. Never compensate with homemade load-bearing shims or altered electrical hardware.
Arm, rail or hanging kit?
| Option | Useful when | Reason to skip |
|---|---|---|
| Tank arm | Both connections and service clearances are documented | Clamp cannot seat as instructed or lid cannot open |
| Multi-light rail | The maker supports the fixture count and complete rail configuration | Unsupported span, missing bracket or unclear support requirements |
| Hanging kit | The fixture maker approves it and a suitable support is professionally established | Unknown load-bearing structure; do not improvise a ceiling anchor |
| Existing mount | Exact fixture generation and tank fit remain supported | Damage, missing parts or an undocumented adapter |
Reusing the correct existing mount is a valid no-buy result. Changing a light does not automatically require changing a rail, but retain it only after checking the new fixture’s mounting documentation. Conversely, a visually similar bracket is not proof of compatibility.
Access sketch: plan the movement, not just the resting position
Side view to sketch: tank rear panel → clamp envelope → arm reach → fixture center. Mark the lid’s opening arc and the vertical path needed to lift out equipment. Record the lowest obstruction above the fixture and the gap behind the tank. Do not use this sketch as a structural calculation or an installation procedure.
Fictional decision: an owner’s fixture bracket matches, but the rear clamp would occupy the same space as the lid hinge. They keep their current working mount while requesting a documented alternative. “Buy the matching brand” would have missed this conflict.
Worked example: a 1-3/8 inch limit on paper
EcoTech lists the RMS Single Arm at 1-3/8 inches maximum tank/trim thickness (about 35 mm) and 13 inches of clearance above the RMS (about 330 mm). Say a made-up tank has 3/4 inch (19 mm) glass with a 1/2 inch (13 mm) plastic trim band on top. The stack is 1-1/4 inches, so it passes the thickness limit with 1/8 inch to spare.
Passing thickness clears one row of the worksheet, not the whole mount. If that trim is molded around an overflow at the clamp spot, the clamp can't seat flat and the answer is still no. Write both results in the "Pass / unknown" column. Our rule of thumb: one unknown is enough reason to hold the order.
Before any order
List included adapters, missing parts and the manufacturer instruction revision in the worksheet. Confirm current availability separately. In particular, do not assume the older BRS ReefLED 90 mounting-arm listing is available; this guide makes no stock recommendation for it. Mount fit is separate from choosing light output: use the reef light guide and PAR guide for lighting needs.
Frequently asked questions
Does a brand match guarantee fit?
No. Verify the full fixture model, generation, bracket and tank contact surface.
Can I modify the clamp to clear trim?
Do not improvise load-bearing modifications. Obtain a manufacturer-approved configuration or choose another mount.
Where the numbers come from
Sources checked November 8, 2026: the two EcoTech pages listed here. The worksheets and the fictional examples are ours, and we haven't tested any mount. Confirm the exact fixture, bracket and revision with the maker before you order.
If the worksheets show a gap
The links go to category and general-store pages, not to a specific mount, and they aren't a stock check. If your current mount passed every row, there's nothing to buy. If something failed, take the completed worksheets to the retailer or maker and confirm the part and its availability there.
Disclosure: Coral Compass may earn a commission when you buy through links on this page, at no extra cost to you. Retailer links are marked as sponsored, and this doesn't change what we recommend. Full disclosure.
Shop reef LED light fixtures at Bulk Reef Supply (affiliate link)
Browse Bulk Reef Supply (general store; search and verify the needed item) (affiliate link)