Titanium vs glass: what changes when you buy
| Titanium element (e.g. BRS titanium) | Glass heater (e.g. Eheim Jager) | |
|---|---|---|
| Breakage | Shatterproof metal tube | Glass body; handle and mount with care |
| Thermostat | Usually none: needs an external controller | Built in; controller recommended as backup |
| Typical length | BRS 100–300 W: 10.25 in; 600 W: 14 in | Jager 100 W: 31.9 cm; 200 W: 40.6 cm; 300 W: 50.6 cm |
| Water level | Fully submersible (per BRS) | Must be submerged at least to the MIN. WATER LEVEL mark |
| Warranty listed | 3 years on the heating element (BRS) | See the maker's current terms |
Sources: BRS 300W Titanium Heater with Finnex Controller listing; Eheim thermocontrol (Jager) 3611–3619 manual. Checked Nov 5, 2026.
Heater length vs sump depth
Measure the water depth in the chamber where the heater will sit, at the lowest level your ATO allows. A glass heater must stay submerged to its marked minimum line, so a 300 W Eheim Jager (about 50.6 cm, 19.9 in) is too tall for many sump chambers that hold 8–10 in of water. Two shorter heaters, or titanium elements (10.25 in for BRS's 100–300 W sizes), are easier to fit. Leave room to reach the heater for cleaning and to keep it out of the skimmer and return pump intake.
| Eheim Jager wattage | Length (Ø 36 mm) |
|---|---|
| 50 W | 243 mm (9.6 in) |
| 75 W | 270 mm (10.6 in) |
| 100 W | 319 mm (12.6 in) |
| 150 W | 345 mm (13.6 in) |
| 200 W | 406 mm (16.0 in) |
| 250 W | 452 mm (17.8 in) |
| 300 W | 506 mm (19.9 in) |
Controller compatibility
| Controller | Max load | Probe | Alarms and notes |
|---|---|---|---|
| Inkbird ITC-306T | 10 A, 100–240 V (about 1,200 W at 120 V); heating only, two outlets | NTC, 2 m (6.56 ft), IP67 probe | High-temperature and sensor-fault alarms; day/night set points; Wi-Fi version available. Body and socket are not waterproof. |
| Finnex HC-820M (in BRS titanium bundles) | Up to 1,000 W, 110–120 V | Remote sensor, 32 in cord, magnetic mount | Cuts power if the sensor is out of water; overheat alarm. Not Apex compatible; not effective in RO/DI water. |
| Aquarium controller (Apex and similar) | Per the outlet strip's rating | Controller temperature probe | Check the maker's outlet rating and add up every heater on that strip. |
Sources: Inkbird ITC-306T product specs; BRS titanium heater bundle listing (HC-820M). Checked Nov 5, 2026.
Worked example: 300 W of heat on one controller
Say the heater size calculator comes back at 300 W for a 75 US gallon system. The same 300 W can arrive as one heater or two, and the controller sees the same load either way. What changes is length and what a stuck heater does. Controller load is watts divided by the rating in the table above (the Inkbird's 10 A at 120 V is 1,200 W).
| Setup | Length of each heater | Load on Inkbird ITC-306T (1,200 W) | Load on Finnex HC-820M (1,000 W) | Heat added if one sticks on |
|---|---|---|---|---|
| One 300 W Eheim Jager | 506 mm (19.9 in) | 25% | 30% | 300 W |
| Two 150 W Eheim Jager | 345 mm (13.6 in) each | 25% | 30% | 150 W |
| One 300 W BRS titanium | 10.25 in (260 mm) | 25% | 30% | 300 W |
Our own arithmetic on the stuck-on case: 300 W warms 284 L of water by about 0.9 °C (1.6 °F) an hour before any heat loss, and 150 W warms it about half that. Real tanks lose heat to the room and to evaporation, so the rise is slower, but a heater that sticks on overnight still has hours to work. That is the reason this page keeps telling you to split the wattage and to set a controller cutoff just above your target.
Our pick order is fit first, controller rating second, brand last. A heater that can't stay submerged to its marked line is the wrong heater, however good the reviews are. Splitting the load across two glass heaters also shortens each one to 345 mm. That helps, though 13.6 in is still tall for a chamber that holds 8–10 in of water, so measure before you buy. BRS lists its 100–300 W titanium elements at one length, so splitting wattage costs titanium buyers nothing in fit; check BRS's current size list before you order. If what you want is a full reef controller such as Apex or Hydros rather than a heater thermostat, start with our Apex vs Hydros vs GHL comparison.
Before you buy: compatibility checklist
- Wattage: from the heater size calculator, split across two heaters.
- Fit: heater length vs water depth at the lowest level, plus clearance.
- Controller load: total watts on the controller well under its rating.
- Probe: long enough to reach the display or sump, in saltwater, away from the heater.
- Alarms: high and low temperature alerts, or a controller that cuts power on a fault.
- Voltage: 120 V vs 230 V models are not interchangeable.
Disclosure: Coral Compass may earn a commission when you buy through links on this page, at no extra cost to you. Retailer links are marked as sponsored, and this doesn't change what we recommend. Full disclosure.
Compare current titanium and glass heaters and controllers in aquarium heaters at Bulk Reef Supply(affiliate link). For summer overheating instead, see the reef tank temperature guide.
Reef heater FAQ
Is a titanium heater better than glass for a reef tank? Titanium can't shatter and has no glass to crack, which is why many sump owners prefer it. Most titanium elements have no built-in thermostat, so they need an external controller. Glass heaters like the Eheim Jager have a thermostat built in but must be handled carefully and submerged to the marked minimum water level.
Do I need a heater controller? For a titanium element without a thermostat, yes. For a glass heater with its own thermostat, a controller is a strongly recommended failsafe: set it to cut power a little above your target so a heater that sticks on can't cook the tank.
How many watts can a heater controller handle? Check the controller's rating and add up every heater on it. Inkbird lists the ITC-306T at 10 A total (about 1,200 W at 120 V); BRS lists the Finnex HC-820M in its titanium bundle at up to 1,000 W. Stay well under the limit.
Will a heater fit in my sump? Compare the heater's length with the water depth in the chamber where it goes. A 300 W Eheim Jager is about 50.6 cm (19.9 in) long and must be submerged to its minimum line; BRS's 100–300 W titanium elements are 10.25 in long. Shallow sumps often need a shorter titanium element or a heater mounted at an angle if the maker allows it.
What size heater do I need? Size from your heat loss, not just gallons. Use the reef heater size calculator, then split the total across two heaters so a single failure is less dangerous.
Is a controller probe safe in RO/DI water? Not always. BRS notes the Finnex HC-820M is not effective in low-TDS or RO/DI water, so keep its probe in the tank or sump saltwater, not the top-off reservoir.
Sources
- BRS: 300W Titanium Aquarium Heater w/ Finnex Controller(affiliate link) (checked Nov 5, 2026)
- Eheim thermocontrol 3611–3619 (Jager) manual (checked Nov 5, 2026)
- Inkbird ITC-306T specifications (checked Nov 5, 2026)